I have made two versions; a 3 bottle per layer version and a 2 bottle per layer version. The 3-bottle version requires a 300mm print bed, while the 2-bottle version can be printed on a 250mm bed.

These wine crates are made from only two parts; the fixed end walls and the folding side walls (you need two of each for each layer of the “crate”). These parts all snap together and then the completed structure folds to collapse for storage when not needed.

Printing

I have tried to make my main print settings visible on the Cura screenshot but in case they are difficult to read I have summarized them here…

Material: I choose to use PETG for its durability and flexibility.

My Setup:
Nozzle = 0.4mm

My Settings:
Layer height = 0.2mm
Line width = 0.4mm
Wall count = 4 (1.6mm)
Infill = 40%

Support:
No support needed.

Print Orientation: As shown in the screenshot(s).

Assembly Notes

The post Wine Stackers – Folding Stackable Wine Crate first appeared on logicalplanet.

This 380mm diameter lazy Susan can be printed on a 220mm print bed! I feel that is pretty awesome. It feeds my confidence to tackle more challenges like this and opens the door for designs I could not imagine before.

The Design

To achieve this design, I created a second layer to the top and bottom of the Lazy Susan concept. These new layers become the mounting frame for the inner layer (the Lazy Susan layer). Then with all rings quartered and offset 45 degrees from each other, the frames hold the inner layer in place.

With these additional mounting layers the original design height of 9mm increases to 11.4mm which is still quite thin all things considered.

The pin carriers are also in quarters but do not connect. They simply float around inside the Lazy Susan and push each other around as needed.

Printing

A minimum bed size of 220mm x 220mm is required to print these parts.

I have tried to make my main print settings visible on the Cura screenshot but in case they are difficult to read I have summarized them again here…

Material: I choose to use PETG for its durability and flexibility.

My Setup:
Nozzle = 0.4mm

My Settings:
Layer height = 0.2mm
Line width = 0.45mm
Wall count = 4 (1.6mm)
Infill = 40%

Support:
Designed to print without support. Do not add support.

Print Orientation: As shown in the screenshot(s).

Assembly Notes

This design requires no fasteners, hardware or adhesives. But I do recommend adding a very thin layer of synthetic lubricant.

Try to insert the pins into the pin carrier from the bottom (print-bed side). And, keep the bottom (print-bed side) of the assembled carrier downward in the completed assembly.

When assembling the final quarter of the top or bottom assembly, you will not be able to slide in the part completely. The final portion should snap into the mounting portion of the assembly.

Future

I think I have just about exhausted the whole Lazy Susan thing but there is one more gigantic design I may tackle one day. I want to make a Lazy Susan that is about 1.25m (~4ft) in diameter for my crawl space. I have space but it is awkward to access so making an enormous Lazy Susan would be the perfect solution to store more and keep it accessible. In that case, I would have to print the circumference in 12 or 16 pieces (I am guessing). And, that would bring some more challenges.

The post 380mm Lazy Susan Printed on a 220mm Bed!! first appeared on logicalplanet.

The Kanger is a keyboard hanger which allows you to store your keyboard on the top back of your monitor to make more desk space. Totally designed out of need, I made this because my desk is just too cluttered and I was constantly looking for somewhere to put my keyboard.

I have not tried it on so many monitors to know it will fit all but I believe it will fit most. The top hook component has a depth of 25mm so as long as the top of your monitor is not more than that it should rest on your monitor well.

While the Kanger folds up and can be put away when not needed it really can just stay on your monitor so that it is there when you want to put your keyboard somewhere.

I have listed this as a product on my bukudesign.com site and as such I have an instructional graphic made which I will include here…

Printing

This is a one-piece print-in-place design with no support required. I am using a 0.4 nozzle with the line set to 0.45mm. With these settings, the detents and hinges print well. If you find them too loose try matching these settings. And please give me feedback if you have any.

Material: I choose to use PETG for its durability and flexibility.

My Setup:
Nozzle = 0.4mm

My Settings:
Layer height = 0.2mm
Line width = 0.45mm
Wall count = 4 (1.6mm)
Infill = 40%
Support = Designed to print without supports.

Print Orientation: As shown in the screenshot.

The post Kanger™ first appeared on logicalplanet.